Pro Camera Pan and Tilt Kit

Pro Camera Pan and Tilt Kit

Pro Camera Pan and Tilt Kit

Retail Price: Starting at: $34.99

This is the new carbon reinforced plastic pan/tilt FPV module that uses a custom mechanism allowing for full 180 degree (+/- 90 degree) panning with a standard servo without the need for a servo stretcher.  A full 360 degree pan (+/- 180 degrees) is possible with the use of an extended travel servo or an NG Hobbies SSV3.5 servo stretcher (option below).  Rather than supporting the weight of the camera on the weak servo connection, the pan is mounted to a super-durable metal mechanism rotating on precision bearings.

The modules are supplied with options for various servos servos depending on your budget or requirements.

Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation.

The module can be attached to the plane of your choice with four screws. Dimensions listed below in the pictures.

The included camera mounts includes extended screws for a solid mount of all the "full size" Ready Made RC, LLC  cameras, including the RMRC-420, RMRC-480, RMRC-540, RMRC-600XV, RMRC-700XV.  It includes a pop out rear panel for the cameras with built in on screen controls. 

Smaller cameras may be mounted using double sided adhesive foam tape (not included).  Some cameras not listed above may require modifications to the camera mount.  We hope to add additional camera brackets soo!

Note: Currently the back plates are designed for the pan/tilt system being installed on top of the aircraft.  If you plan on mounting the assembly inverted under the aircraft, some modifications to the back plate may be required.

This kit includes:

  • Precision laser cut fiber reinforced components and required gears, bearings, and other hardware for pan/tilt module.
  • Two 9g Servos  (default option)

Note: for the "no servo" option, it is up to the customer to modify the assembly if required.  The system was designed for the servos listed in the options below.  Any other servo must be aligned properly for proper gear engagement.

You'll need to supply:

  • Zip-ties to hold for holding your wiring in place.
  • Medium CA
  • 5 minute epoxy

Manual: Pro Pan/Tilt Module


  • Model: PRO-PANTILTKIT
  • Shipping Weight: 0.3
  • 13 Units in Stock
  • Manufactured by or for: RMRC - Made in China

Please Choose:



Misc Options





Order in the next 27min and it ships today!


Customers who bought this product also purchased...

APC 11x5.5E Prop

APC 11x5.5E Prop

Price:   $3.68
APC 11x5.5E Prop

RMRC - M3 Bobbins for Flight Controller - 5x5mm - Black (4pc)

RMRC - M3 Bobbins for Flight Controller - 5x5mm - Black (4pc)

Price:   $4.79
Vibration dampening bobbins designed specifically for flight controllers. These have proven to be 100% durable during our testing and have also shown...
RMRC - M3 Bobbins for Flight Controller - 5x5mm - Black (4pc)

F4 Flight Controller MPU6000 Gyro

F4 Flight Controller MPU6000 Gyro

Price:   $26.99
Features: 36mm x 36mm (standard 30.5mm between mounting holes) Support raceflight and betaflight firmware Use MPU6000 gyro Gyro and MCU have 3.3V...
F4 Flight Controller MPU6000 Gyro

Blue Series 2600kV MT2205 Motor - CW Thread

Blue Series 2600kV MT2205 Motor - CW Thread

Price:   $18.99  $15.99 Save: 16% off
Based off the Tiger Motor MT series motor the RMRC 2205 2600KV motor brings efficiency, power, and smoothness to your racing...
Blue Series 2600kV MT2205 Motor - CW Thread

SMA Female to SMA Female Adapter

SMA Female to SMA Female Adapter

Price:   $3.99
SMA Female to SMA Female adapter. Note:  To avoid possible component damage, please make sure you are using the correct connector for your...
SMA Female to SMA Female Adapter

Fat Shark Dominator 1.3GHz Receiver Module

Fat Shark Dominator 1.3GHz Receiver Module

Price:   $37.99
Now shipping updated version FSV2443 - 8ch version The NexwaveRF 1.3 GHz receiver module with 8 channels as a modular receiver for use with...
Fat Shark Dominator 1.3GHz Receiver Module