The Holybro SiK Telemetry Radio V3 100mW 433MHz 2 pcs (SKU: 17012) is a compact, full-duplex, open-source wireless telemetry transceiver pair engineered to establish a real-time MAVLink data link between Pixhawk-standard UAV flight controllers and a Ground Control Station (GCS). Operating across the 414MHz to 460MHz sub-GHz frequency band with a maximum RF output power of 100mW (20 dBm), this matched two-radio set provides dependable out-of-the-box communication ranges exceeding 300 meters using the included 2dBi antennas, and can be extended to several kilometers with directional ground antennas.
Built around open-source SiK firmware and an integrated FT230X USB-to-UART converter IC, both air and ground transceivers are completely interchangeable. The radios utilize Frequency Hopping Spread Spectrum (FHSS) across up to 50 hopping channels alongside forward error correction capable of repairing up to 25% of bit errors. Weighing just 23.5 grams each with antenna attached, the modules feature a 6-pin JST-GH 3.3V TTL serial interface for plug-and-play connection to Pixhawk flight controllers and a Micro-USB port (with included USB-A, Type-C, and OTG adapters) for seamless connection to Windows, macOS, Linux, or Android ground stations running Mission Planner or QGroundControl.
Interchangeable Air & Ground Transceivers: Both radio modules are hardware- and firmware-identical, allowing either unit to serve on the aircraft or at the ground station.
Open-Source SiK Firmware & MAVLink Framing: Optimized specifically for low-latency MAVLink telemetry packets with built-in forward error correction that recovers up to 25% of bit errors.
433MHz FHSS Interference Immunity: Operates across 414MHz–460MHz using Frequency Hopping Spread Spectrum across up to 50 channels and 256 configurable Network IDs (0–255) to prevent multi-vehicle cross-talk.
Two-Way Full-Duplex Communication: Adaptive Time Division Multiplexing (TDM) UART interface supports simultaneous bidirectional telemetry streaming, parameter adjustments, and mission uploads.
Plug-and-Play Pixhawk & GCS Connectivity: Includes both a 6-pin JST-GH to JST-GH cable for modern Pixhawk autopilots and a JST-GH to Molex DF13 adapter cable for legacy Pixhawk/Pix32 boards, plus USB-A, Type-C, and OTG cables for laptops and mobile devices.
Integrated FT230X USB-to-UART Bridge: Built-in serial conversion IC enables driver-free COM port recognition and configuration via Mission Planner, APM Planner, or AT commands.
Brand / Manufacturer: Holybro
Model Identifier: SiK Telemetry Radio V3 (100mW 433MHz, 2-Piece Set)
Manufacturer SKU / Part Number: 17012
Frequency Band: 414 MHz – 460 MHz (433MHz Regional Variant)
Maximum RF Output Power: 100 mW (20 dBm, adjustable)
Receive Sensitivity: -121 dBm @ 2 kbps RF data rate / -105 dBm @ 64 kbps RF data rate
RF Data Rates: 2, 4, 8, 16, 32, 64 (default), 96, 128, 192, 250 kbps
Serial Interface Data Rates: 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6 (default), 115.2 kbps
Spread Spectrum & Channels: Frequency Hopping Spread Spectrum (FHSS), up to 50 hopping channels, configurable duty cycle
Network Addressing & Topology: Point-to-Point; Network ID: 0 – 255
Firmware & Protocol Framing: Open-Source SiK Firmware; Standard transparent serial or MAVLink protocol framing
Error Correction: Forward Error Correction (corrects up to 25% of bit errors)
USB-to-UART Chipset: FT230X / FT23 USB to BASIC UART IC
Air Serial Interface: 6-Pin JST-GH Connector (3.3V TTL UART)
Ground USB Interface: Micro-USB Port (with USB-A, Type-C, and OTG adapters)
Antenna Connector & Gain: RP-SMA Female; 2 dBi Omnidirectional Whip Antennas included
Input Supply Voltage: 5V DC (powered via USB or flight controller JST-GH port)
Transmit Current: 100 mA @ 20 dBm
Receive Current: 25 mA
Operating Temperature Range: -40°C to +85°C
Module Dimensions: 28.0 mm x 53.0 mm x 10.7 mm (excluding antenna)
Net Weight: 23.5 grams per module (with antenna)
Autopilot & GCS Compatibility: Pixhawk 4, Pixhawk 5X, Pixhawk 6C, Pixhawk 6X, Durandal, Pix32; ArduPilot & PX4 via Mission Planner and QGroundControl
(2) Holybro SiK Telemetry Radio V3 Modules (100mW, 433MHz) with 2dBi RP-SMA Antennas
(1) Micro-USB to USB-A Cable
(1) Micro-USB to Micro-USB OTG Adapter Cable
(1) Micro-USB to USB Type-C Adapter
(1) 6-Pin JST-GH to 6-Pin JST-GH Cable (for Pixhawk Standard Flight Controllers)
(1) 6-Pin JST-GH to 6-Pin Molex DF13 Cable (for Pix32, Pixhawk 2.4.6, and legacy autopilots)
| Name | Value |
|---|---|
| MANUFACTURER | RFDesign |