Pix32 Pixhawk & M8N GPS & PM & 915 Telemetry V3 Set
by Holybro

The Holybro Pix32 is the next step in FC hardware with its powerful ST micro 32bit ARM Cortex core and massive I/O support. The Pix32 is one of the most advanced autopilot systems available with support for almost any type of vehicle from a moon rover or a multirotor aircraft, even a submarine! Designed by the PX4 open-hardware project, it is supported by a number of development communities making this one of the most flexible and reliable platforms for vehicle control, with many features and functions sure to be available in the future.

Features:
• Advanced 32 bit ARM Cortex® M4 Processor running NuttX RTOS
• 14 PWM/servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible)
• Abundant connectivity options for additional peripherals (UART, I2C, CAN)
• Integrated backup system for in-flight recovery and manual override with dedicated processor and stand-alone power supply
• Backup system integrates mixing, providing consistent autopilot and manual override mixing modes
• Redundant power supply inputs and automatic failover
• External safety button for easy motor activation
• Multicolor LED indicator
• High-power, multi-tone piezo audio indicator
• MicroSD card for long-time high-rate logging
• Super precise digital GPS with compass
• Telemetry with OSD (433Mhz/915Mhz)
 

Specs

• Input Voltage: 2~12s (7.4~51V)
• Size: 81x44x15mm
• Weight: 33.1g

Microprocessor

• 32-bit STM32F427 Cortex M4 core with FPU
• 168 MHz/256 KB RAM/2 MB Flash
• 32 bit STM32F103 failsafe co-processor

Sensors

• ST Micro L3GD20 3-axis 16-bit gyroscope
• ST Micro LSM303D 3-axis 14-bit accelerometer / magnetometer
• Invensense MPU 6000 3-axis accelerometer/gyroscope
• MEAS MS5611 barometer

Interfaces

• 5x UART (serial ports), one high-power capable, 2x with HW flow control
• 2x CAN
• Spektrum DSM / DSM2 / DSM-X® Satellite compatible input up to DX8 (DX9 and above not supported)
• Futaba S.BUS® compatible input and output
• PPM sum signal
• RSSI (PWM or voltage) input
• I2C®
• SPI
• 3.3 and 6.6V ADC inputs
• External microUSB port

POWER

• PCB Current: total 120A outputs (MAX)
• UBEC input voltage : 7~51v (2~12s LiPo) 
• Voltage and current measurement configured for 5V ADC 
• Switching regulator outputs 5.2V and 3A max 
• 6-pos Molex cable plugs directly to APM/Pix32's 'PM' connector 
• 6-pos GH cable plugs directly to Pixhawk4/Pixhawk4 mini 'PM' connector

GPS
Holybro enabled this new GPS for you to work with Pix32（PX4_2.4.6）. It has UBLOX M8N module on it, as well as IST8310 compass and tri-colored LED indicator. Also the Safety switch on it will make the connection more convenient and simple.
This module ships with a baud rate of 38400 5Hz.

Included

• Pix32 autopilot
• Buzzer
• Safety switch button
• GPS compass module with mounting bracket and pre-wired connectors
• 433/915Mhz Telemetry radio system 
• 10s power module with XT60 connectors and 6-position connector cable
• Extra 6-position cable
• Micro USB cable
• SD card
• Various pieces of mounting foam
• 3-wire servo cable
• I2C splitter module with cable 

Note: pix32 is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers allow for PPM output, but some, such as non-S.BUS Futaba receivers do not.

*PX4/Pixhawk is an independent, open-source, open-hardware project aiming at providing a high-end autopilot to the academic, hobby and industrial communities (BSD licensed)