The HEE WING T1-S Ranger VTOL with Stabilizer, PNP FPV Airplane 790mm EPP FPV Gray (Model: T1-S-V-PNP-45) is a turnkey, modular vertical take-off and landing (VTOL) fixed-wing FPV platform engineered for runway-free launches, confined-space operations, and automated long-range cruising. Expanding upon the original T1 Ranger airframe with a 790mm wingspan and 715mm fuselage length, the T1-S VTOL utilizes a tricopter tilt-rotor propulsion layout—combining two front wing-mounted tilting brushless motors with a rear tail-boom vertical lift motor—to hover and transition seamlessly between multicopter and forward fixed-wing flight.
Unlike the bare PNP airframe variant, the T1-S-V-PNP-45 package arrives pre-equipped with the factory HEE WING FX-405 VTOL Flight Controller / Stabilizer, specialized 2S–6S PMU (0–50A current sensor), and GNSS/GPS + Compass module, pre-flashed and pre-tuned with ArduPilot QLoiter/VTOL parameters out of the box. Molded from crash-resistant EPP foam in an FPV Gray finish, the airframe features an enlarged internal avionics bay for digital HD video transmitters (such as DJI O3/O4 Air Units or Walksnail Avatar) or analog FPV systems, snap-fit quick-release wings with integrated electrical connectors, a quick-release carbon tail boom, upper-mounted aileron servos, and a custom-molded EPP foam travel and storage case.
Pre-Configured FX-405 VTOL Stabilizer & GPS Suite: Includes the STM32F405-based FX-405 flight controller (ICM-42688 IMU, SPL06 barometer, MAX7456 OSD, 9 PWM outputs, 4 UARTs), dedicated 0–50A PMU, and GPS/compass module pre-loaded with ArduPilot VTOL/QLoiter parameters for automated vertical hover and forward transitions.
Tricopter Tilt-Rotor VTOL Propulsion: Pairs two front wing-mounted tilting 1806 2000KV brushless motors driven by V39 metal-gear tilt servos with a rear tail-boom lift motor for stationary hovering, vertical takeoffs/landings, and efficient wing cruising.
Expanded 790mm Wingspan & Enlarged Avionics Bay: Increased wingspan and fuselage volume improve glide efficiency and provide ample space for digital HD air units, GPS hardware, receivers, and high-capacity 4S batteries.
Tool-Free Modular Quick-Release Assembly: Snap-fit main wings with integrated quick-disconnect wiring plugs and a quick-release carbon tail boom enable rapid field setup and breakdown without tools.
Upper-Mounted Aileron Servo Architecture: Positions aileron servos and control linkages on the top surface of the wings, protecting linkages from grass snags and impact damage during uneven landings.
Broad Receiver & Video Compatibility: FX-405 stabilizer natively supports ExpressLRS (ELRS), TBS Crossfire (CRSF), SBUS, PPM, and iBUS receivers alongside both Analog OSD and Digital HD VTX systems.
Included Molded EPP Travel & Storage Case: Ships inside a form-fitting EPP foam carrying case that protects the fuselage, tilt nacelles, wings, and tail assembly during transport.
Manufacturer Model / SKU: T1-S-V-PNP-45
Completion Level: Plug-and-Play with Stabilizer & GPS (PNP+FC — Motors, ESCs, Tilt Servos, Control Surface Servos, FX-405 VTOL Stabilizer, PMU, and GPS pre-installed/included; Receiver, Battery, and FPV gear required)
VTOL Configuration: Tricopter Tilt-Rotor (2x Front Tilting Wing Motors + 1x Rear Tail Lift Motor)
Airframe Material: Molded EPP Foam with Carbon Fiber Reinforcement Spars & Tail Boom
Color Finish: FPV Gray
Wingspan: 790 mm
Fuselage Length: 715 mm
Takeoff Weight Range: 600 g – 950 g (depending on battery and FPV payload configuration)
Motors: (3) 1806 2000KV Brushless Motors (2x Front Tilting, 1x Rear Tail Lift)
Electronic Speed Controllers (ESCs): (3) HEE WING 20A BLS Brushless ESCs
Tilt Servos: (2) HEE WING V39 Metal-Gear Digital Tilt Servos (with metal tilt mounts)
Control Surface Servos: (3) 4.3g Micro Servos (2x Upper-Mounted Aileron, 1x Elevator)
Propellers: (3) 5126 (5.1" x 2.6") 2-Blade Propellers
Recommended Battery: 4S LiPo (1300mAh–2200mAh) or 4S Li-Ion (3000mAh–4000mAh) (4S power required for VTOL hover and transitions)
Transport Case: Custom-Molded EPP Storage & Transportation Foam Case (Included)
Flight Controller MCU: STM32F405
IMU (Gyro / Accelerometer): ICM-42688
Barometer: SPL06 / SLP06
OSD Chipset: MAX7456 (Analog OSD) + Digital HD VTX Support
Blackbox Storage: Onboard Dataflash
Interfaces: 4x UARTs, 9x PWM Outputs
Pre-Loaded Firmware: ArduPilot VTOL / QLoiter Parameters (T1-S VTOL tuned)
Supported RC Protocols: ELRS, CRSF (Crossfire), SBUS, PPM, iBUS
PMU Input Voltage & Current Rating: 2S – 6S LiPo (7.4V – 22.2V DC); 0 – 50A Rated Current
GNSS / GPS Module: HEE WING BE-250Q / BE-250i GPS with Integrated Compass
Stabilizer Dimensions & Weight: 44.3 mm x 34.4 mm x 13.7 mm; 14.2 grams (excluding PMU and cables)
(1) HEE WING T1-S Ranger VTOL Molded EPP Fuselage (with hatch and pre-installed wiring)
(1) Left Main Wing (with pre-installed 1806 2000KV motor, V39 tilt servo mechanism, 20A BLS ESC, 4.3g aileron servo, and quick-release plug)
(1) Right Main Wing (with pre-installed 1806 2000KV motor, V39 tilt servo mechanism, 20A BLS ESC, 4.3g aileron servo, and quick-release plug)
(1) Carbon Fiber Tail Boom Assembly (with pre-installed rear 1806 2000KV lift motor, 20A BLS ESC, and 4.3g elevator servo)
(1) Horizontal Tail Stabilizer
(1) Vertical Tail Fin
(1) Carbon Fiber Main Wing Spar Rod
(1) HEE WING FX-405 VTOL Stabilizer / Flight Controller (pre-loaded with ArduPilot VTOL parameters)
(1) HEE WING 2S–6S 50A Power Management Unit (PMU)
(1) HEE WING GPS + Compass Module (BE-250Q / BE-250i)
(1) USB-C Adapter & Plug-and-Play Interconnect Cable Set
(1) Propeller Set containing (3) 5126 Propellers
(1) Battery Mounting Plate & Control Linkage Hardware Pack
(1) Custom-Molded EPP Storage & Transportation Foam Case
(1) T1-S VTOL Assembly & Setup Guide
(1) 6-Channel or Greater Radio Transmitter and Compatible RC Receiver (supporting ELRS, CRSF, SBUS, PPM, or iBUS)
(1) 4S LiPo (1300mAh–2200mAh) or 4S Li-Ion (3000mAh–4000mAh) Flight Battery (4S voltage required for VTOL flight)
(1) Compatible 4S LiPo/Li-Ion Balance Battery Charger
(Optional) FPV Camera, Video Transmitter (DJI O3/O4 Air Unit, Walksnail, or Analog VTX), and FPV Goggles / Monitor
(Optional) Foam-Safe CA Glue (for securing control horn buckles during final assembly)
| Name | Value |
|---|---|
| MANUFACTURER | Hee Wing |